WS2801 Flat-Pack RGB Pixel displays are digitally-controllable LED lights which can be set to any color, or animated. Each display contains an RGB LED along with a dedicated WS2801 controller chip. We have models that are weatherproof and sealed in clear silicon casing and others that are open-frame. The weatherproof models feature flanges molded in so that you can 'push' them into a 12mm drill holes in materials up to 1.5mm/0.06" thick.

The RGB pixel is connected by a 4-conductor cable. Data is shifted down from one pixel to the next so that you can easily cut the strand or attach more onto the end. The four connection wires carry the following signals: +5V (Red), Gnd (Yellow), Data (Green) and Clock (Blue).

Pixels are digitally controlled, with an internal 8-bit PWM LED driver (24-bit color for 16 million different shades). Pixels must be clocked by a microcontroller, or other control devices. There are many examples around the web available showing simple connections and code for the Arduino as well as other microcontrollers.

Each pixel contains an 8mm diffused (frosted) RGB LED, with a 120 degree beam width. Brightness of the display for each color is approximately Red = 3.3 Lumens/300 mcd, Green = 10 Lumens/1000 mcd, Blue = 2.7 Lumens/300 mcd (mcd calculation based on full 120 degree beam) for a total of approximately 1600mcd and due to the diffused frosting design of the LED light is evenly distributed.

The pixel displays are sold in strands of 25 or 50 pixels with a JST SM 4-pin connector on each end allowing you to chain modules together. Each strand also has additional power connection wires to allow for power modules separately and not trying drawing power through the whole chain.

A complete datasheet with specifications on the WS2801 driver chip is also available.

Technical Details:

  • Modules measure 26.5mm wide, 18.5mm deep, and 22.2mm tall and are designed to fit into a 12mm mounting hole
     
  • Spacing between modules is 15.5cm (155mm) (center of one pixel to the center of the next)
     
  • 25 or 50 pixel modules per strand
     
  • Pixels utilize WS2801 chip for full 24 bit color
     
  • 5V power, 60mA maximum per pixel (LED on full white) 2-pin SPI-like protocol
     
  • Brightness of the display for each color is approximately Red = 3.3 Lumens/300 mcd, Green = 10 Lumens/1000 mcd, Blue = 2.7 Lumens/300 mcd (mcd calculation based on full 120 degree beam) for a total of approximately 1600mcd and due to the diffused frosting design of the LED light is evenly distributed
     

Notes:

  • Modules are designed to run on 5v DC. Exceeding the power specification most certainly will damage pixel modules.
     
  • Embossed on the side of the module is an arrow (?) which indicates the direction of flow for the displays. Your signal input must be placed on the input to the module.
     
  • For strings of modules less than 50-pieces, you may not receive any kind of JST SM connector at all, as they will be cut from a standard string of 50.
Reviews about Flat WS2801 Pixel - Insulated
Average rating: 0 reviews
Total reviews: 0
Write your own review on this product.
Write a review
Sort by:

Write a review

Please login or register to review

Flat WS2801 Pixel - Insulated

  • String of 25 or 50 Modules

  • Product Code: FLAT-PIXEL-INSUL
  • Availability: In Stock
  • $33.00 USD


Available Options


Related Products

Flat WS2801 Pixel

Flat WS2801 Pixel
Single Pixel

 Single Module

$1.50 USD $0.50 USD

Flat WS2801 Uninsulated Pixel String

Flat WS2801
Uninsulated Pixel String

 String of 25 or 50 Modules

$31.00 USD

RGB Dual LED Module

RGB Dual
LED Module

 

$3.25 USD

WS2801 Bullet Pixel - Insulated

WS2801 Bullet Pixel
Insulated

 String of 50 Modules

$39.95 USD

Tags: flat, ws2801, pixel, insulated, pieces, modules flat-pixel-insul-50 based